Commercial

Heat Fab

Heat Fab 4326SS Saf-T Vent 3" Diameter - 304 Storm Collar

$27.00 $18.95

 Storm Collar - For use on horizontal or vertical systems when a Heat-fab wall or roof penetration is not used or is not required. The storm collar may be tightened and sealed around the vent to prevent water from entering the building. It may also...

Add to Cart

Heat Fab

Heat Fab 4327SS Saf-T Vent 3" Diameter - 304 Support Clamp

$25.00 $17.95

 Outer Jacket Support Clamp - For use on horizontal systems to provide support at the required 6-foot intervals. May be used singly as a saddle to rest the vent in and hung from two rods or cables. Use in pairs by clamping around the outer jacket...

Add to Cart

Heat Fab

Heat Fab 5300CI Saf-T Vent EZ Seal - 3" Storm Collar & Rain Cap

$210.00 $147.95

 Heat Fab 5300CI Saf-T Vent EZ Seal - 3" Storm Collar & Rain Cap Heat Fab Saf-T Vent EZ Seal is the fastest and most reliable venting solution for Category I, II, III, and IV gas appliances – with no RTV sealant required. Saf-T Vent venting...

Add to Cart

Heat Fab

Heat Fab 5381CI Saf-T Vent 3" Diameter - Roof Flashing 2" to 8" Pitch

$275.00 $192.95

 Pitched Cone Flashing- For use with single-wall or double-wall Saf-T Vent systems with vertical terminations. Can be used on roofs with a 2/12 - 8/12 pitch. This part comes with a tall storm collar and is made of all stainless steel construction...

Add to Cart

Heat Fab

Heat Fab 5390CI Saf-T Vent EZ Seal 3" Diameter Wall Penetration & Horizontal Termination

$319.00 $223.95

 Heat Fab 5390CI Saf-T Vent EZ Seal. Wall Penetration & Horizontal Termination - For Saf-T Vent EZ Seal systems with horizontal terminations. Use to penetrate any combustible or non-combustible wall. This part is a thimble only and does not...

Add to Cart

Heat Fab

Heat Fab 7000RTVL RTV Sealant - 550 DEG MAX - 10 oz Tube

$155.00 $108.95

 Heat Fab 7000RTVL RTV Sealant. Use to seal the system. In order to have a UL Listed system, Saf-T Vent CI Plus parts without a factory adhered seal must be installed with approved RTV sealants. Also, use RTV Sealant when connecting Saf-T vent EZ...

Add to Cart

Heat Fab

Heat Fab 7000TUBE-10 Drain Tube Hose Kit - 3/8" x 10' Long

$50.00 $35.95

 Condensate Drain Tube Kit- This kit contains a length of 3/8" diameter high temperature silicone rubber tubing, a 3/8" spring clamp, and two cable ties. The silicone tubing is rated for 500 degree F, and is translucent to allow inspection of the...

Add to Cart

Heat Fab

Heat Fab 7001SIL-5 Silicone Gasket Lube - 5 oz Tube

$33.00 $23.95

  Heat Fab 7001SIL-5 Silicone Gasket Lube - 5 oz Tube. Apply lubricant to the seal to improve ease of installation before connecting parts. Allows for easier assembly and disassembly. Heat Fab 7001SIL-5 Silicone Gasket Lube 5 ounce tube Apply...

Add to Cart

Heat Fab

Heat Fab 7001TUBE Drain Tube Hose Kit - 1/2" x 10' Long

$98.00 $68.95

 Condensate Drain Tube Kit- This kit contains a length of 1/2" diameter high temperature silicone rubber tubing, a 1/2" spring clamp, and two cable ties. The silicone tubing is rated for 500 degree F, and is translucent to allow inspection of the...

Add to Cart

Heat Fab

Heat Fab 73EXPKIT Saf-T Vent EZ Seal Field Expander Kit

$89.00 $62.95

A field expander kit is available for 3" diameter Saf-T Vent installations. The field expander is a tool the installer can use to recreate the male taper on a cutoff piece of pipe. Heat Fab 73EXPKIT - Field Expander Kit A field expander kit is only...

Add to Cart

Heat Fab

Heat Fab 9301 Saf-T Vent EZ Seal - 3 Inch Diameter - 6" Straight Length

$32.00 $22.95

 6" Length - Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9301AMTK Saf-T Vent EZ Seal - 3" Ametek Inducer Adapter

$52.00 $36.95

 Heat Fab 9301AMTK Saf-T Vent EZ Seal - 3" Ametek Inducer Adapter 9301AMTK 3" Ametek Inducer Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: Buderus GA124, 17, 23, 30; GA244, 27, 44, 53; G124X, 18, 25,...

Add to Cart

Heat Fab

Heat Fab 9301BG Saf-T Vent EZ Seal 3" Diameter Blast Gate

$135.00 $94.95

 Heat Fab 9301BG Saf-T Vent EZ Seal 3" Diameter Blast Gate. Use to balance the draft of an appliance when the vent is terminated with a fan. Heat Fab 9301BG 3" Diameter Blast Gate Saf-T Vent EZ Seal Use to balance the draft of an appliance when...

Add to Cart

Heat Fab

Heat Fab 9301BSH Saf-T Vent EZ Seal - 3" Bosch Adapter

$50.00 $35.95

 Heat Fab 9301BSH Saf-T Vent EZ Seal - 3" Bosch Adapter 9301BSH 3" Bosch Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: Bosch AquaStar 250 Bosch Pro Tankless GWH-635-ES EZ Seal Catalog &...

Add to Cart

Heat Fab

Heat Fab 9301MOD Saf-T Vent EZ Seal - 3" Modine HD Adapter

$63.00 $44.95

 Heat Fab 9301MOD Saf-T Vent EZ Seal - 3" Modine HD Adapter 9301MOD 3" Modine HD Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: Modine Hot Dawg HD30 thru HD75   EZ Seal Catalog & Dimensional Data ...

Add to Cart

Heat Fab

Heat Fab 9301PAL Saf-T Vent EZ Seal - 3" Paloma Adapter

$79.00 $55.95

 Saf-T Vent EZ Seal - 3" Paloma Adapter 3” Paloma Adapter 9301PAL Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following untits: Rheem Pronto! 4.2 / RTG-42 Norwitz N-042 Paloma PH-16UFN, PH-16UFH, PH-16FS EZ Seal...

Add to Cart

Heat Fab

Heat Fab 9301PVC Saf-T Vent EZ Seal - 3" PVC Adapter

$103.00 $72.95

 Heat Fab 9301PVC Saf-T Vent EZ Seal - 3" PVC Adapter Heat Fab 9301PVC 3" PVC Adapter Saf-T Vent EZ Seal Works on the following units: Alpine - ALP080, ALP105, ALP150, ALP210 Lochinvar Knight - KBN080 thru KBN401 Lochinvar Armor - AWN151 thru...

Add to Cart

Heat Fab

Heat Fab 9301UTI Saf-T Vent EZ Seal - 3" Utica DV & Columbia CDV Adapter

$50.00 $35.95

 Heat Fab 9301UTI Saf-T Vent EZ Seal - 3" Utica DV & Columbia CDV Adapter 9301UTI 3" Utica DV & Columbia CDV Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: Columbia Boiler - CDV38 trhu CDV125 ...

Add to Cart

Heat Fab

Heat Fab 9301VSMN Saf-T Vent EZ Seal - 3" Viessman Adapter

$52.00 $36.95

 Heat Fab 9301VSMN Saf-T Vent EZ Seal - 3" Viessman Adapter 9301VSMN 3" Viessman Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: Viessmann Vitoden 200 WB2 6-24 & 8-32   EZ Seal Catalog &...

Add to Cart

Heat Fab

Heat Fab 9302 Saf-T Vent EZ Seal - 3 Inch Diameter - 12" Straight Length

$39.00 $27.95

 12" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9304 Saf-T Vent EZ Seal - 3 Inch Diameter - 18" Straight Length

$56.00 $39.95

 18" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9305 Saf-T Vent EZ Seal - 3 Inch Diameter - 24" Straight Length

$68.00 $47.95

  24" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9307 Saf-T Vent EZ Seal - 3 Inch Diameter - 37.5" Straight Length

$89.00 $62.95

  37.5" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9308 Saf-T Vent EZ Seal - 3 Inch Diameter - 48" Straight Length

$136.00 $95.95

  48"" Length- Install vent with a continuous pitch of 1/4" per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9310 Saf-T Vent EZ Seal - 3 Inch Diameter - 30 Degree Elbow

$84.00 $58.95

  30° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 3 feet of vent. 3" Diameter 30° Elbow Saf-T...

Add to Cart

Heat Fab

Heat Fab 9311 Saf-T Vent EZ Seal - 3 Inch Diameter - 45

$84.00 $58.95

 45° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 5 feet of vent for 3 and 4 inch diameters. 3” Diameter...

Add to Cart

Heat Fab

Heat Fab 9312 Saf-T Vent EZ Seal - 3 Inch Diameter - 70

$101.00 $70.95

 70° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 8 feet of vent. 3” Diameter 70° Elbow Saf-T Vent...

Add to Cart

Heat Fab

Heat Fab 9314 Saf-T Vent EZ Seal - 3 Inch Diameter - 90 Elbow

$101.00 $70.95

  90°  Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 10 feet of vent. Heat Fab 9314 Saf-T Vent EZ...

Add to Cart

Heat Fab

Heat Fab 9314LR Saf-T Vent EZ Seal - 3 Inch Diameter - 90

$101.00 $70.95

  90° Loose Radius Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 10 feet of vent. Heat Fab 9314LR Saf-T...

Add to Cart

Heat Fab

Heat Fab 9314TERM Saf-T Vent EZ Seal - 3" 90 Degree Screen Elbow Termination

$105.00 $73.95

 Elbow Termination with Screen - Use as a termination on horizontal or vertical systems, as specified or allowed by the appliance manufacturer. 3” Diameter 90° Elbow with Screen Termination Saf-T Vent EZ Seal AL29-4C Stainless Steel   ...

Add to Cart

Heat Fab

Heat Fab 9316 Saf-T Vent EZ Seal - 3" Conduit Tee

$95.00 $66.95

 Conduit Tee - A conduit tee, when installed horizontally, may be fitted with a drain tee cover to create a condensate drain. Due to its high pressure drop, the conduit tee is generally not used to make a transition from horizontal to vertical...

Add to Cart

Heat Fab

Heat Fab 9316B Saf-T Vent EZ Seal - 3" Boot Tee

$177.00 $123.95

 Boot Tee - Use vertically or horizontally to add appliances into a common-vent system. When installed horizontally, the male end of the tee body may be capped off with a tee cover to allow for future appliances. When used in conjunction with a...

Add to Cart

Questions & Phone Orders

SDS Supply Corp.
13731 S. Route 30, Unit 105
Plainfield, IL 60544
Call us: (800) 236-9029

Shop with Confidence

Safe & Secure shopping online. Learn more

Payment Methods

Top