Commercial

Heat Fab

Heat Fab 4426SS Saf-T Vent 4" Diameter - 304 Storm Collar

$27.00 $18.95

 Storm Collar - For use on horizontal or vertical systems when a Heat-fab wall or roof penetration is not used or is not required. The storm collar may be tightened and sealed around the vent to prevent water from entering the building. It may also...

Add to Cart

Heat Fab

Heat Fab 4427SS Saf-T Vent 4" Diameter - 304 Support Clamp

$25.00 $17.95

  Outer Jacket Support Clamp - For use on horizontal systems to provide support at the required 6-foot intervals. May be used singly as a saddle to rest the vent in and hung from two rods or cables. Use in pairs by clamping around the outer jacket...

Add to Cart

Heat Fab

Heat Fab 5400CI Saf-T Vent EZ Seal - 4" Storm Collar & Rain Cap

$216.00 $151.95

 Rain Cap - Use as a termination on vertical systems. Category I and II appliances require a raincap or other device to prevent rainwater from entering the vent. Vent systems for positive pressure appliances may omit the raincap if there are other...

Add to Cart

Heat Fab

Heat Fab 5481CI Saf-T Vent 4" Diameter - Roof Flashing 2" to 8" Pitch

$328.00 $229.95

 Pitched Cone Flashing- For use with single-wall or double-wall Saf-T Vent systems with vertical terminations. Can be used on roofs with a 2/12 - 8/12 pitch. This part comes with a tall storm collar and is made of all stainless steel construction...

Add to Cart

Heat Fab

Heat Fab 5490CI Saf-T Vent 4" Diameter Wall Penetration & Horizontal Termination

$352.00 $246.95

    Heat Fab 5490CI Saf-T Vent EZ Seal. Wall Penetration & Horizontal Termination - For Saf-T Vent EZ Seal systems with horizontal terminations. Use to penetrate any combustible or non-combustible wall. This part is a thimble only and does...

Add to Cart

Heat Fab

Heat Fab 7000RTVL RTV Sealant - 550 DEG MAX - 10 oz Tube

$155.00 $108.95

 Heat Fab 7000RTVL RTV Sealant. Use to seal the system. In order to have a UL Listed system, Saf-T Vent CI Plus parts without a factory adhered seal must be installed with approved RTV sealants. Also, use RTV Sealant when connecting Saf-T vent EZ...

Add to Cart

Heat Fab

Heat Fab 7000TUBE-10 Drain Tube Hose Kit - 3/8" x 10' Long

$50.00 $35.95

 Condensate Drain Tube Kit- This kit contains a length of 3/8" diameter high temperature silicone rubber tubing, a 3/8" spring clamp, and two cable ties. The silicone tubing is rated for 500 degree F, and is translucent to allow inspection of the...

Add to Cart

Heat Fab

Heat Fab 7001SIL-5 Silicone Gasket Lube - 5 oz Tube

$33.00 $23.95

  Heat Fab 7001SIL-5 Silicone Gasket Lube - 5 oz Tube. Apply lubricant to the seal to improve ease of installation before connecting parts. Allows for easier assembly and disassembly. Heat Fab 7001SIL-5 Silicone Gasket Lube 5 ounce tube Apply...

Add to Cart

Heat Fab

Heat Fab 7001TUBE Drain Tube Hose Kit - 1/2" x 10' Long

$98.00 $68.95

 Condensate Drain Tube Kit- This kit contains a length of 1/2" diameter high temperature silicone rubber tubing, a 1/2" spring clamp, and two cable ties. The silicone tubing is rated for 500 degree F, and is translucent to allow inspection of the...

Add to Cart

Heat Fab

Heat Fab 9401AMTK Saf-T Vent EZ Seal - 4" Ametek Inducer Adapter

$71.00 $49.95

 Saf-T Vent EZ Seal - 4" Ametek Inducer Adapter 9401AMTK 4" Ametek Inducer Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: Buderus GA244 62 Nortec GHB / GHP / GHMC 200 and 400 Takagi (see adapter...

Add to Cart

Heat Fab

Heat Fab 9401BG Saf-T Vent EZ Seal 4" Diameter Blast Gate

$138.00 $96.95

 Heat Fab 9401BG Saf-T Vent EZ Seal 4" Diameter Blast Gate. Use to balance the draft of an appliance when the vent is terminated with a fan. Heat Fab 9401BG 4" Diameter Blast Gate Saf-T Vent EZ Seal Use to balance the draft of an appliance when...

Add to Cart

Heat Fab

Heat Fab 9401DUN Saf-T Vent EZ Seal - 4" Dunkirk Adapter

$69.00 $48.95

  Heat Fab 9401DUN Saf-T Vent EZ Seal - 4" Dunkirk Adapter Heat Fab 9401DUN 4" Dunkirk Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: Crown Boiler XE Series Dunkirk Radiator XE Series H.B. Smith PVG-2 thru...

Add to Cart

Heat Fab

Heat Fab 9401FUL Saf-T Vent EZ Seal - 4" Fulton Pulse Adapter

$197.00 $137.95

  Heat Fab 9401FUL Saf-T Vent EZ Seal - 4" Fulton Pulse Adapter. For Fulton Boiler Works PulsePak PHW-300, PHW-500, PHW-750, PHW-950, PHW-1000 9401FUL 4" Fulton Pulse Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following...

Add to Cart

Heat Fab

Heat Fab 9401MACH Saf-T Vent EZ Seal - 4" P-K Mach Adapter

$129.00 $90.95

  Heat Fab 9401MACH Saf-T Vent EZ Seal - 4" P-K Mach Adapter. P-K Mach Adapter - This adapter is specially designed to connect directly to the vent outlet of P-K Mach Boilers, Series C-300, C-450, C-900, and C-1050. 9401MACH 4" P-K Mach Adapter...

Add to Cart

Heat Fab

Heat Fab 9401PVI Saf-T Vent EZ Seal - 4" PVI Power VT Adapter

$65.00 $45.95

 Heat Fab 9401PVI Saf-T Vent EZ Seal - 4" PVI Power VT Adapter 9401PVI 4" PVI Power VT Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: PVI Industries Power VT (all models)   EZ Seal Catalog &...

Add to Cart

Heat Fab

Heat Fab 9401RHM Saf-T Vent EZ Seal - 4" Rheem Adapter

$53.00 $37.95

 Saf-T Vent EZ Seal - 4" Rheem Adapter 9401RHM 4" Rheem Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: Paloma Industries PH-28RIFS Rheem PH28 Rheem Pronto1 7.4 / RTG74 WaiWela PH28RIFS &...

Add to Cart

Heat Fab

Heat Fab 9401RYPK Saf-T Vent EZ Seal - 4" Raypak Hi-Delta Adapter

$54.00 $37.95

 Saf-T Vent EZ Seal - 4" Raypak Hi-Delta Adapter 9401RYPK 4" Raypak Hi-Delta Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: A.O. Smith Pro Star XT 194 Noritz N-063S, N-069M, N-084M, N-084M-DV ...

Add to Cart

Heat Fab

Heat Fab 9401SRI Saf-T Vent EZ Seal - 4" Sta-Rite Adapter

$63.00 $44.95

 Saf-T Vent EZ Seal - 4" Sta-Rite Adapter 9401SRI 4" Sta-Rite Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: Sta-Rite Industries Max-E-Therm SR Pool and Spa Heaters   EZ Seal Catalog & Dimensional...

Add to Cart

Heat Fab

Heat Fab 9401VSMN Saf-T Vent EZ Seal - 4" Viessman Adapter

$71.00 $49.95

 Heat Fab 9401VSMN Saf-T Vent EZ Seal - 4" Viessman Adapter 9401VSMN 4" Viessman Adapter Saf-T Vent EZ Seal AL29-4C Stainless Steel Works on the following units: Viessmann Vitoden WB2 11-44 & 15 -60   EZ Seal Catalog &...

Add to Cart

Heat Fab

Heat Fab 9402 Saf-T Vent EZ Seal - 4 Inch Diameter - 12" Straight Length

$46.00 $32.95

 12" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9404 Saf-T Vent EZ Seal - 4 Inch Diameter - 18" Straight Length

$68.00 $47.95

 18" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9405 Saf-T Vent EZ Seal - 4 Inch Diameter - 24" Straight Length

$74.00 $51.95

  24" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9407 Saf-T Vent EZ Seal - 4 Inch Diameter - 37.5" Straight Length

$107.00 $74.95

 37.5" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9408 Saf-T Vent EZ Seal - 4 Inch Diameter - 48" Straight Length

$149.00 $104.95

 48" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9409 Saf-T Vent EZ Seal - 4 Inch Diameter - 15

$109.00 $76.95

 15° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 3 feet of vent. Heat Fab 9409 Saf-T Vent EZ Seal 4”...

Add to Cart

Heat Fab

Heat Fab 9410 Saf-T Vent EZ Seal - 4 Inch Diameter - 30

$109.00 $76.95

  30° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 3 feet of vent. 4” Diameter 30° Elbow Saf-T...

Add to Cart

Heat Fab

Heat Fab 9411 Saf-T Vent EZ Seal - 4 Inch Diameter - 45

$109.00 $76.95

 45° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 5 feet of vent for 3 and 4 inch diameters. 4” Diameter...

Add to Cart

Heat Fab

Heat Fab 9412 Saf-T Vent EZ Seal - 4 Inch Diameter - 70

$132.00 $92.95

 70° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 8 feet of vent. 4” Diameter 70° Elbow Saf-T Vent...

Add to Cart

Heat Fab

Heat Fab 9414 Saf-T Vent EZ Seal - 4 Inch Diameter - 90

$132.00 $78.28

 90° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 10 feet of vent for 3 and 4 inch diameters. Heat Fab...

Add to Cart

Heat Fab

Heat Fab 9414LR Saf-T Vent EZ Seal - 4 Inch Diameter - 90

$132.00 $92.95

 90° Elbow- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 10 feet of vent. 4” Diameter 90° LR Elbow...

Add to Cart

Heat Fab

Heat Fab 9414TERM Saf-T Vent EZ Seal - 4" 90 Degree Screen Elbow Termination

$140.00 $98.95

  Elbow Termination with Screen - Use as a termination on horizontal or vertical systems, as specified or allowed by the appliance manufacturer. 4” Diameter 90° Elbow with Screen Termination Saf-T Vent EZ Seal AL29-4C Stainless Steel   ...

Add to Cart

Heat Fab

Heat Fab 9416 Saf-T Vent EZ Seal - 4" Conduit Tee

$100.00 $70.95

 Conduit Tee - A conduit tee, when installed horizontally, may be fitted with a drain tee cover to create a condensate drain. Due to its high pressure drop, the conduit tee is generally not used to make a transition from horizontal to vertical...

Add to Cart

Questions & Phone Orders

SDS Supply Corp.
13731 S. Route 30, Unit 105
Plainfield, IL 60544
Call us: (800) 236-9029

Shop with Confidence

Safe & Secure shopping online. Learn more

Payment Methods

Top