Commercial

Heat Fab

Heat Fab 4626SS Saf-T Vent EZ Seal - 6 Inch Diameter - 304 STORM COLLAR

$31.00 $21.95

 304 STORM COLLAR- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 3 feet of vent. Heat Fab 4626SS Saf-T Vent EZ...

Add to Cart

Heat Fab

Heat Fab 4627SS Saf-T Vent 6" Diameter - 304 Support Clamp

$23.00 $16.95

 Outer Jacket Support Clamp - For use on horizontal systems to provide support at the required 6-foot intervals. May be used singly as a saddle to rest the vent in and hung from two rods or cables. Use in pairs by clamping around the outer jacket...

Add to Cart

Heat Fab

Heat Fab 5600CI Saf-T Vent EZ Seal - 6" Storm Collar & Rain Cap

$234.00 $163.95

Rain Cap - Use as a termination on vertical systems. Category I and II appliances require a rain cap or other device to prevent rainwater from entering the vent. Vent systems for positive pressure appliances may omit the rain cap if there are other...

Add to Cart

Heat Fab

Heat Fab 5690CI Saf-T Vent 6" Diameter Wall Penetration & Horizontal Termination

$418.00 $292.95

Heat Fab 5690CI Saf-T Vent EZ Seal. Wall Penetration & Horizontal Termination - For Saf-T Vent EZ Seal systems with horizontal terminations. Use to penetrate any combustible or non-combustible wall. This part is a thimble only and does not include...

Add to Cart

Heat Fab

Heat Fab 5691CI Saf-T Vent 6" Diameter Insulated Wall Penetration

$377.00 $263.95

Wall Penetration Assembly - without Screen - Use to penetrate any combustible or non-combustible wall. This part is a thimble only and does not include any vent. Order enough vent to pass through the thimble and extend at least 4 inches beyond a...

Add to Cart

Heat Fab

Heat Fab 7000RTVL RTV Sealant - 550 DEG MAX - 10 oz Tube

$155.00 $108.95

 Heat Fab 7000RTVL RTV Sealant. Use to seal the system. In order to have a UL Listed system, Saf-T Vent CI Plus parts without a factory adhered seal must be installed with approved RTV sealants. Also, use RTV Sealant when connecting Saf-T vent EZ...

Add to Cart

Heat Fab

Heat Fab 7000TUBE-10 Drain Tube Hose Kit - 3/8" x 10' Long

$50.00 $35.95

 Condensate Drain Tube Kit- This kit contains a length of 3/8" diameter high temperature silicone rubber tubing, a 3/8" spring clamp, and two cable ties. The silicone tubing is rated for 500 degree F, and is translucent to allow inspection of the...

Add to Cart

Heat Fab

Heat Fab 7001SIL-5 Silicone Gasket Lube - 5 oz Tube

$33.00 $23.95

  Heat Fab 7001SIL-5 Silicone Gasket Lube - 5 oz Tube. Apply lubricant to the seal to improve ease of installation before connecting parts. Allows for easier assembly and disassembly. Heat Fab 7001SIL-5 Silicone Gasket Lube 5 ounce tube Apply...

Add to Cart

Heat Fab

Heat Fab 7001TUBE Drain Tube Hose Kit - 1/2" x 10' Long

$98.00 $68.95

 Condensate Drain Tube Kit- This kit contains a length of 1/2" diameter high temperature silicone rubber tubing, a 1/2" spring clamp, and two cable ties. The silicone tubing is rated for 500 degree F, and is translucent to allow inspection of the...

Add to Cart

Heat Fab

Heat Fab 9601 Saf-T Vent EZ Seal - 6 Inch Diameter - 6" Straight Length

$39.00 $27.95

 6" Length - Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9602 Saf-T Vent EZ Seal - 6 Inch Diameter - 12" Straight Length

$59.00 $41.95

  12" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9604 Saf-T Vent EZ Seal - 6 Inch Diameter - 18" Straight Length

$87.00 $60.95

 18" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9605 Saf-T Vent EZ Seal - 6 Inch Diameter - 24" Straight Length

$101.00 $70.95

  24" Length- Install vent with a continuous pitch of 1/4” per foot, sloping upward toward the termination (unless otherwise specified by the appliance manufacturer). It is important to provide adequate support to a Saf-T Vent EZ Seal system...

Add to Cart

Heat Fab

Heat Fab 9610 Saf-T Vent EZ Seal - 6 Inch Diameter - 30 DEG ELBOW

$137.00 $95.95

  30 DEG ELBOW- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 3 feet of vent. Heat Fab 9610 Saf-T Vent EZ Seal 6"...

Add to Cart

Heat Fab

Heat Fab 9611 Saf-T Vent EZ Seal - 6 Inch Diameter - 45

$137.00 $95.95

 45° Elbow - Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 8 feet of vent for 6 inch diameter elbows. Heat Fab...

Add to Cart

Heat Fab

Heat Fab 9616B Saf-T Vent EZ Seal - 6" Boot Tee

$271.00 $189.95

Boot Tee - Use vertically or horizontally to add appliances into a common-vent system. When installed horizontally, the male end of the tee body may be capped off with a tee cover to allow for future appliances. When used in conjunction with a drain tee...

Add to Cart

Heat Fab

Heat Fab 9616BAR Saf-T Vent EZ Seal - 6" Barometric Tee

$137.00 $95.95

 Heat Fab 9616BAR Saf-T Vent EZ Seal Stainless Steel 6 Inch Diameter Barometric Tee Heat Fab 9616BAR 6” Diameter Barometric Tee Saf-T Vent EZ Seal AL29-4C Stainless Steel EZ Seal Catalog & Dimensional Data EZ Seal...

Add to Cart

Heat Fab

Heat Fab 9617D Saf-T Vent EZ Seal - 6" Condensate Tee Cover 3/8" Drain

$93.00 $65.95

Tee Cover with Drain Fitting - Use at the base of a tee or boot tee to drain away condensate from a vent system. This type of tee cover may also be used on the leg of a tee that is installed horizontally, to create a drain in a horizontal run. High...

Add to Cart

Heat Fab

Heat Fab 9621 Saf-T Vent EZ Seal - 6 Inch Diameter - HORZ/VERT IN-LINE 1/2 DRAIN

$105.00 $73.95

  HORZ/VERT IN-LINE 1/2 DRA- Use to achieve offsets or changes in the direction of the vent system. The degree of these welded seam elbows is not adjustable. The pressure drop for each elbow is equivalent to 3 feet of vent. Heat Fab 9621 Saf-T...

Add to Cart

Heat Fab

Heat Fab 9690 Saf-T Vent EZ Seal - 6 Inch Diameter - Mitered Termination with Screen

$160.00 $112.95

 Mitered Termination with Screen - Use as a termination on horizontal or vertical systems, as specified or allowed by the appliance manufacturer. 6” Diameter Mitered Termination with Screen Saf-T Vent EZ Seal AL29-4C Stainless Steel   ...

Add to Cart

Heat Fab

Heat Fab 96GUY Saf-T Vent EZ Seal - Guy Support Section 6" Diameter

$204.00 $142.95

 Guy Support Section - Provides vertical support using a part that is a flue-gas-carrying component of the vent system. Guy sections are primarily installed in long, inaccessible chases or used to provide support to systems with extended lengths...

Add to Cart

Questions & Phone Orders

SDS Supply Corp.
13731 S. Route 30, Unit 105
Plainfield, IL 60544
Call us: (800) 236-9029

Shop with Confidence

Safe & Secure shopping online. Learn more

Payment Methods

Top